A place where one woman has gathered resources and information to help her family survive in an uncertain future; together with occasional personal musings.

Monday, January 4, 2010

more useful articles

Stovepipe maitenance


The season is arriving. The garden is ready for its final turning, the apples are picked, and it’s supposed to freeze by the end of the week. So, how is your creosote level? Not your cholesterol, your creosote. It builds up on the inside of your chimney and stove pipe, not your veins, but it could cause similar problems.

Tap your stove pipe. Are you answered with a sharp ping or a thud? If it is the latter, you have a creosote problem.

Creosote is the black substance, usually dry and flaky, but in some cases liquid or goopy, that collects on the lining of the chimney or stove pipe, restricting the diameter of the flue. This decreases the draft and reduces the heat flow out of the stove pipe by insulating the walls so that not enough heat is absorbed or transferred through the pipe. If the flames and gases reach a temperature of 1000°, the creosote will ignite, causing a chimney fire.

Creosote is formed from the condensation of organic vapors, tar acids, and water which escape when full combustion is not achieved. The magnitude of the deposit depends on the density of the smoke and fumes and the surface temperature of the stove pipe or chimney on which the vapors are condensing.

There is no way to really avoid the problem, only decrease it. All wood has some moisture, and at some point all fires cool down. This combination of moisture and the cooling process produces the gases which form the creosote. The only way to combat the problem is to control the flaky black adversary with proper use and cleaning of the stove.

The best way to decrease creosote buildup is to keep the temperature of the stovepipe and chimney hot. Creosote does not begin to form until the surface temperature drops to 250° or below. Make the fire burn hot after the fire box has been reloaded. Do not burn large un-split logs, as these reduce the amount of air circulation necessary to facilitate complete combustion and allows more gases and tar to escape from the slow-burning log. Never extinguish a fire quickly. The quick cooling process emits large amounts of unwanted gases and water.

Green wood is especially dangerous to any creosote already in the lining of the pipe. This is especially true of green softwood, because it pops and explodes, sending sparks in every direction. The sparks could easily lodge in the uneven terrain and ignite.

Chimneys and stovepipes should be cleaned at least twice during the burning season (more frequently if the heat source is used year-round). A good way to estimate is to clean after every two to three cords of wood.

Do not use your stove as a trash incinerator. Plastics emit an exceedingly corrosive acid, which will magnify any existing creosote problem. Because creosote is such an excellent insulator (more effective than asbes-tos), a very thin layer can reduce the efficiency of your stove by 10 to 15%. Dampers are big collectors of creosote. Like any variety of debris, creosote collects on any type of angle or protrusion where the exhaust gases are slowed down. Therefore, vertical stovepipes collect less creosote than a pipe with a number of angles or elbows, because the gases can move at a brisker pace.

There are products on the market which claim to keep the chimney free of creosote, but they do not clean existing creosote off of the interior. The cleaning needs to be done either by a chimney sweep or by you, using similar methods.

If you don’t believe the extremely combustible nature of creosote, try burning a few flakes and see how they almost explode into flame.

A chimney fire sounds something like a locomotive roaring through the next room, accompanied by shooting and exploding flames. The heat of a creosote fire can be so intense that it can actually extricate the mortar from between the stones or bricks and send the heat-filled particles crashing onto the roof.

If you have a chimney fire, call the fire department. If possible, close the damper. Any attempt to put out the fire should be done with an abundance of rock salt or baking soda, but never with water. Water would simply intensify the problem, creating more steam and gas and possibly cracking the chimney liners or the cast iron body of the stove and pipes.

Keeping your stove free from creosote will give you a more efficient and safer burning season, so after the stove has been properly cleaned you can relax and worry about your cholesterol level instead.



Slaughtering and Butchering

Fall is butchering time, a period of joy in the harvest of the year’s work and of sadness that the lives of your beautiful, healthy animals have come to an end. On this occasion the animals should be treated with the same kindness and respect with which they were treated during their lives. Good farmers raise their animals free from fear, anxiety and stress. The animals should meet their end as they lived, without the terror of the slaughterhouse.

Making careful preparations will help you remain calm. After years and years of butchering I still feel a strong adrenaline rush when the animal is killed. Be prepared for that and use it to make sure the death is as painless as possible. A knowledgeable person can direct these strong feelings into doing the job right instead of letting their emotions get the best of them and botching the job. When the temperature only reaches 40° during the day and the pasture is no longer adequate feed, it is time to butcher. Sheep and goats should be nine months or under. Pigs should be just slightly jowly.

Past wisdom dictated that 250 pounds was optimum butchering weight for a pig, but after your porkers reach 225, the ratio of weight gain going to fat versus lean meat increases dramatically. After many years of experimentation, I try for 200 pounds. At that point my pigs have no more of a fat covering than my goats. There’s still enough fat for lard and sausage, but there’s no reason to pour more and more feed into them only to find their kidneys so imbedded in fat that they’re hard to locate. I buy my pigs in early May and by mid-November they are eating so voraciously that I know it can no longer be practical to keep them.

Figure 1.  Cutting around the foot.Figure 1. Cutting around the foot.

Calves are traditionally kept until they are 10-15 months old, but that can be a problem for a family raising their own meat. If the calf was born in February it could be butchered in December. In a place like Montana, however, December is late for butchering. With the temperatures around 0°, your meat would have to hang a very long time to age.

If you decided to keep the calf till spring, you would be faced with deciding whether to butcher it after feeding all winter or to let it grow some on the pasture.

By the time the calf is looking really big, it’s midsummer. In a cool climate you could butcher it then if you did it fast, but you would have to pay someone to hang it to age. In most climates, you don’t butcher between May and October anyway, if you can help it, because of the fly problem. So then you’re up to fall when you have all the other butchering to do. If you can manage it, I think that is your best option.

Here are a few additional suggestions to think about ahead of time. Butchering pigs and cows is easier if you withhold food for 24 hours before butchering. This is not totally necessary, and if you would feel bad having your animal hungry on its last day, don’t do it. Just be extra careful with the guts.

When you butcher only certain members of a herd, avoid frightening the others. Don’t run through the herd chasing the one you want. Move slowly and calmly. Try not to kill one animal in front of the others. Don’t slaughter in the animal’s home.

Figure 2.  Cutting down the body.Figure 2. Cutting down the body.

The exception to this is when you are slaughtering pigs. Swine do not care if you kill their companion and will rush over to drink the blood if they can.

It makes sense to leave the pig butchering until last so that they can consume anything that is left over. Don’t feed surplus fat to pigs, though. Only poultry can convert fat into useable production calories. That is because of their high rate of metabolism. If you feed fat to pigs, it will provide calories, but it can only become fat, not meat.

Before butchering, decide what parts you will save. I think I’ve tried saving just about everything, and I think there’s some value in that. However, if no one wants to eat it, the value is only in learning and experimenting and knowing the possibilities.

There is a certain satisfaction in using everything. Ears and tail can flavor a pot of beans. Hooves can make gelatin. Stomachs can hold blood sausage and other things. Lungs are edible. Intestines can be used to make sausage casings or cooked in some other additional dishes. I will describe what I keep, but feel free to make your own decisions about what you and your family would like to try.

A word about using the intestines for sausage. If the situation is such that you have running water in a hose, it is fairly easy to clean them. Otherwise you’ll have to do it indoors, which is a lot of work. After that you have to turn them inside out and scrape them.

If you don’t scrape them, they’ll still be edible but they’ll be tougher than you might like. These days I feed the intestines to the animals and buy prepared ones. If you buy them from a butcher house, they’re already prepared and quite inexpensive. Try not to buy them in the grocery store, as they demand ridiculous prices.

Be sure to save enough fat for lard, sausage making, and if you’re butchering a cow, for ground beef.

A goat is shot in the back of the head. The front is too hard. With a cow or a pig, mentally draw lines from the top of each ear to the opposite eye. Where the lines cross is where you shoot. One shot with a .22 should do it.

Figure 3.  Skinning from the center.Figure 3. Skinning from the center.

We shoot pigs in their pen. That is the least traumatic for everyone. If you do this, though, you’ll want to get the pig out of the pen as quickly as possible so as to slit the throat on clean ground. Throw a noose around its neck and drag it out. You want to slit the throat while the heart is still beating in order to get all the blood pumped out.

Stick the point of your big knife into the throat and cut outward through the skin. Never try to cut into the skin through the hair. Make sure you’ve severed the main veins and arteries.

Any male animal that is to be used as food should have been castrated. If that wasn’t done, however, remove the head and testicles right away. That’s easy with a goat, but a cow or pig can kick with a real wallop, so be careful. This is done so the meat won’t be tainted.

If you are butchering a pig, you will want to wash it down now. A pig is a clean animal in a natural environment but gets pretty dirty when confined. Be especially careful in cleaning the rear feet, for they’ll stay on unskinned.

Remove the head by cutting all the way around with your big knife. As always, avoid cutting into the hair. Instead keep your knife between the flesh and the skin and cut out. With a goat, twist the head until the bone snaps. With a pig or cow, use your meat saw.

Make slits between the achilles tendon and the ankles and insert the gambrel. At this point, you could scald a pig but in these days of preserving meat by freezing, there’s really no point. In days past, the skin was left on the bacon and hams to protect them. It’s traditional, but there’s no other reason to leave it on since we don’t eat it anyway. And logistically it’s just much simpler to skin. Remove front feet at the joint. Using a pulley for a goat and a come-along for a pig or cow, hoist the animal into the air to a height convenient for working on the rear of the animal.

Slip your short pointed knife (Figure 1) into the slit you made at the achilles tendon and cut around the foot, again cutting out, not in. Be very careful not to cut the tendon. With the knife between the flesh and the skin, slice a line through the skin down each leg to the centerline. Then cut down the body to the neck (Figure 2).

Figure 4.  Skinning the foreleg.Figure 4. Skinning the foreleg.

Now take your skinning knife and begin skinning at the junction where the leg cuts meet the centerline. Hold the skin with one hand or your hook and pull hard to create tension as you use your knife to separate the flesh from the skin. Work out from the center (Figure 3).

If you are not going to use the hide, you won’t have to worry about keeping it intact. Just be concerned about the meat in that case. You’ll have to be much more careful if you want to use the hide.

Keep pulling the skin away with your hand or the hook and continue to slice between the hide and the flesh until the belly is skinned. This will relieve the tension of the skin on the rump. Now work around the leg from front to back.

The next step is to start at the top of the “Y” and skin up and over the crotch. The skin is tightest here, so be especially careful if you’re saving the hide. Pull skin out and down to create tension on your work while you slice with your knife. A layer of fat makes the animal relatively easy to skin. Leave as much fat on the body as possible.

Work over the anus to the tailbone. Give the tail a sharp jerk and it will separate from the vertebrae. From here on, the weight of the skin practically skins the animal for you. Work all around the body. If there is too much movement on the gambrel, lean against the animal.

Raise the beast when it becomes difficult to reach your work. Bring the work to you and stay comfortable. The forelegs are a bit difficult near the shoulders. Start on the outside of the leg (Figure 4). Work around to the front. Skin the neck and the inner forelegs and shed the skin.

Lower the animal so that you can comfortably work on the rear of it. At this point you want to separate the large intestine from the body. You will begin by cutting around the anus with your short pointed knife. Be careful not to make any holes in the intestine. When it is cut free, pull it slightly out and tie it off. It is helpful to have a partner here. This step (tying) is unnecessary if you are butchering a goat.

Figure 5.  Cutting down the belly.Figure 5. Cutting down the belly.

Cut down the belly with your pointed knife. Cut from inside out as before. With your other hand hold the guts away from the point of the knife (Figure 5). Cut through the belly fat all the way down to the sternum. Next, cut the meat between the legs.

If the animal is a male, cut out the penis. Place a large container underneath to catch the guts. By now they will be bulging out of the body. At some point if you are butchering a ruminant, there may be a flow of greenish liquid from the neck. This is just the cud and nothing to worry about.

Cut through the fat surrounding the guts, then sever any tissue connecting them to the rear wall of the body cavity. Pull the anus through to the inside and then out. Separating the intestines from the body is tedious, so take your time. You don’t want to spill the contents into the meat.

Be careful also not to rupture the bladder. Some people tie it and then cut it off, but I’ve found that method to be more likely to cause spillage.

Pull the intestines and bladder out of the body. Most of the stomach will also be free now. You will need to reach in and under to lift it all over the sternum. Some people cut through the sternum, but it’s easy enough just to lift the guts out. Most everything will now be hanging out of the body. Strip away as much of the surrounding belly fat as you can to feed to the chickens. Get out the bowl for the innards you want to keep. Remove the kidneys and fat. Cut out the liver and put it into the keeper bowl along with the kidneys. Sever the remaining flesh connecting the stomachs to the body, and it should all fall into the gut bucket.

Figure 6.  A goat ready to cut up.Figure 6. A goat ready to cut up.

Cut out the diaphragm and remove the lungs and heart by severing the connective tissue behind them. Separate the heart from the lungs and squeeze out the blood from the heart. The heart is a keeper, while the lungs aren’t.

From the neck end, cut out the windpipe. Be sure the opening is clear all the way through the body cavity. Clean all over with cold water. (Now you see that if you hadn’t cleaned those rear feet of a pig, the dirt from them could contaminate the meat.)

Except for pork, we age all our meat from fowl to cow, and strongly advise you to do the same. Pork should only hang overnight to chill, and all meat should be cut up in a chilled state. A goat should age one week in 40° weather, longer in colder weather. If it’s too warm to age it, it’s a real shame to butcher at that time, because the meat won’t be as tender as it could be. A goat is hung whole.

To halve a larger carcass, face the belly while your partner helps hold the body and helps to guide the saw from the back when necessary. Use your fingertips on the blade to guide your cut. A cow should be quartered for ease of handling, of course, but also to allow the meat to cool as quickly as possible. Merely cut between the 2nd and 3rd ribs and be ready to hold the fore section. It should be hung for two weeks under the proper conditions.

When you’re finished working on the animal’s body, it’s time to salvage the tongue and brains from the head. The easiest way to get the tongue is to cut under the jaw in the soft space in the middle. When you have slit this open, reach in and cut the tongue loose from its mooring. Working through the mouth is much harder.

Chopping the skull with an axe works for getting out the brains, but sawing it in half with your meat saw gets the job done with a bit more finesse. If you plan to use the rest of the head, you will have to skin it now. Remove the ears, eyes, nose and anything that doesn’t look like meat or bone. Clean thoroughly. You may want to brush the teeth. You could make goat’s head soup or you could make headcheese. The only heads I use these days are pigs.

Some people use the jowls for bacon, but if you’ve butchered before the pig has gotten really fat, there won’t be much there. I use the head meat for scrapple, tamale meat and pozole. I used to use some in liverwurst, but we prefer these other dishes.

In any case, you’ll need a pot large enough to hold the head. If you cook with a wood stove as I do, just add water to cover, put a lid on and leave it on the stove to simmer until the meat is tender. It’s less convenient if you use some other kind of fuel.

Figure 7.  Separating the rear third of a pig.Figure 7. Separating the rear third of a pig.

Remove the meat and bones from the pot and separate them. Take out anything that looks strange and you’re ready to use whatever recipes you’ve decided on. Boil down your broth to a manageable amount and either use it in your recipes or freeze it for later use.

When you are ready to cut up your meat, refer to the section that applies to your animal. Cutting up a deer or a sheep is the same as a goat.

Cutting up a goat

Cut behind the shoulder blades to remove the front legs. Cut off leg at elbow. These lower legs can be soup bones, but they’re not much good for anything else. You can package the shoulder as it is or you can bone it, roll and tie for a rolled roast. You could also cut it up for stew meat. Take as much meat from the neck as you can. Use that for soup.

You could cut chops if you wanted. You would have to saw through the backbone between every rib to do that. You could bone out the chops to avoid all the sawing. Or you could just cut out the whole muscle bundle along the backbone. It’s called the backscrap and is the best meat on the animal (that’s what I do).

Figure 8.  Separating the front third of a pig.Figure 8. Separating the front third of a pig.

Next take your meat saw and cut the ribs from the backbone. Then cut them in half with your knife for easy packaging. Underneath the backbone is the tenderloin. Cut that out.

Now for the rear third. Cut off the foot. Next cut off the leg at the knee. These are your shanks. Separate the legs at the pelvis. These are the only roasts I keep from a goat. I use the front shoulders for stew or stir fry. You can package the leg as it is or bone it. Boning saves a lot of space and a rolled roast is a pleasure to cut when it’s cooked, too.

That’s it except for working over all the bones to retrieve any last bits of meat for your sausage bucket. I save one goat just for sausage and one for jerky. You may want to do that, or you may have other favorite uses. Goat meat (or chevon as it’s called) is really wonderful when it’s properly handled.

Cutting up a pig

There are many ways to cut up a pig and many ways to cure meat. I’m going to tell you how I do it and why I use this method. If you’re doing your own curing, you have the vagaries of weather to contend with. Below freezing and it doesn’t cure. Fifty degrees and it spoils.

In my first experiments I used an old fashioned cure. It was very salty. The hams and bacon hung in a cool room all year and didn’t spoil. If you don’t have a freezer, you could do that.

You can use a dry cure or a brine cure. In the brine cure, the strength of the brine is det ermined by the amount of meat. Theoretically it can’t get too salty that way, and I have found that to be true.

If you butcher when it’s 40°, and then it warms up to the 50s, then it freezes for a while, then warms up to 50° again, there’s a real danger that your meat will sour around the bone. By the time it’s in the warm smokehouse, you’ve really got trouble. For this reason I bone the hams. I have never had a problem since I began doing this. Also it makes the ham nice to cut when it’s rolled and tied.

Figure 9.  Separating the ribs from the chops.Figure 9. Separating the ribs from the chops.

Your pig should have hung overnight so that the meat is firm. Now you will want to cut your side of pork into thirds. To do this take your meat saw and cut straight down from the backbone through the aitch bone to separate the rear ham from the body. (Blue tape, Figure 7.) The cut should go right through the ball and socket joint. Remove the foot.

To separate the front third, cut between the second and third ribs again cutting straight down from the backbone. (Blue tape, Figure 8.) Look carefully at the muscle bundles and try to keep them intact.

Take the middle section and make another cut after the 11th rib. Then cut across the ribs parallel to the backbone to separate the ribs from the chops. (Blue tape, Figure 9.) Look at both ends of the meat to see where to cut. Remove the belly fat and save it for sausage and lard.

Saw through the backbone for chops and finish your cuts with a knife. It’s helpful to have a partner to hold it steady. Trim off the extra fat but as always, leave some.

Now trim out the loin. Feel the bone with your fingers and just cut out the muscle bundle as well as you can. This is your best roast. Cut it into whatever size you want (Figure 10).

Figure 10.  Rolled poark roasts and the bone they came from.Figure 10. Rolled poark roasts and the bone they came from.

Trim the excess fat from the ribs. Decide whether you want extra meaty ribs or if you want to slice off most of the meat for bacon. Cut the bacon from the ribs (Figure 11). Cut the ribs into easily packaged pieces, but leave the bacon whole until after smoking (Figure 12).

Before cutting your hams, you’ll have to decide whether you want them large or small and how much meat you want for sausage, stir fry, etc. Cutting hams and roasts takes some practice, but don’t worry too much. They can always be trimmed to look nice and nothing is wasted. It can always go into the sausage bucket.

Begin two piles of trimmings. One will be for sausage and the other will be better pieces for stir fry. Take the front third and cut off the hock. If you wanted to make this a shoulder roast you could, but the meat is very fatty and not as good quality as the rear. It could also be used for sausage or stir fry. When you make your roasts, study the muscle bundles and try to keep them intact as much as possible. To bone, cut to the bone and cut around it as well as possible and along the backbone to the third rib. Cut off the front muscle bundle and put it into the sausage bucket. Roll it up as it would be with the bone in and trim it to look nice. Trim off excess fat.

Take the rear third and decide how much hock you want and cut that off. Bone out the rear hams and trim off excess fat. This is tedious, so just take your time. Make your cut in to the bone and cut it out as well as possible. Trim end for looks (Figure 13).

Figure 11.  The bacon separated from the ribs.Figure 11. The bacon separated from the ribs.

Put your bacon, hams and hocks into the curing bucket. Be sure to save enough fat for sausage and lard, and you’re finished with this part.

Cutting up a cow

Begin with the hind quarter. Cut off the leg by making a cut with the meat saw from the hip to the tailbone. If you cut across the top, you will have round steaks. The first cuts are top round and are the best. Thicker cuts make round roasts. The small, less meaty part near the shank is the heel of round. The shank is a soup bone.

The muscle flap on the belly is the flank steak. Cut that off and remove the layers of fat. The rump roast is the meaty end that was cut away from the leg. Bone it out for a rump roast or just cut it off with the saw.

Figure 12. A pig cut up but not yet boned (front)Figure 12. A pig cut up but not yet boned (front)

The top muscle on the remaining piece is all steak. You could cut through the backbone for each steak or bone it out and then cut into steaks. Or the part behind the ribs could be left whole for a sirloin roast. The meat underneath the backbone is the tenderloin or filet mignon which can be removed and cut into steaks (butterfly) or left whole.

Your steaks, beginning at the rear just ahead of the rump roast and moving forward, are sirloin, porterhouse, T-bone, if boned, separate into the filet mignon and New York strip. The rib steaks could be left whole for a rib roast, which would be your best roast. Everything left on this quarter is stew or burger. Stew meat is the better meat. Remove the fat and anything un-meatlike.

Now we’re ready for the front quarter. To remove the leg, lift it up and start cutting underneath until you have cut behind the shoulder blade and separated the leg from the body. The part on the shoulder is called a blade roast. It can be boned or just cut with the saw to the size you prefer. The top part of the leg is chuck and can be made into roasts or steaks. It can be boned or not. The lower part of the leg is burger or soup bone. There are probably a couple of rib steaks on the remaining piece, so cut these out. The neck meat is stew. The meat at the front that would have been just behind the leg is brisket. Remove that from its bone.

Figure 13.  Roasts, hams, chops, bacon, ribs & sausage trimmings.Figure 13. Roasts, hams, chops, bacon, ribs & sausage trimmings.

Cut as many ribs as you want for short ribs. Everything else is stew or burger. When making hamburger, use at least one fourth fat.

Curing

Mix the brine before you cut up your pork, so you can just drop it right in. Two five-gallon buckets of food grade plastic works fine for two pigs. The recipe is for 100 lbs. of meat which should also be right for two pigs. Measure out 8 pounds of pickling salt and 2 pounds of sugar, honey, brown sugar or maple syrup. This is the critical part. Dissolve this in water. We add other spices such as cayenne, black pepper, garlic, etc. but this is only for added flavor and not necessary. The use of boiling water aids in dissolution.

Some people add saltpeter (nitrates), but all it does is make the meat a uniform pink, and I prefer not to use this additive. Bacon and hocks will cure in a week at 40°. Hams will take six weeks. For every day below freezing, another day should be added.

Weight the meat so it doesn’t come above the brine, adding more water if necessary. Use a plate with a clean rock on top.

Figure 14.  Cuts of meat from a pig.Figure 14. Cuts of meat from a pig.

Sausage

Any kind of meat can be used for sausage. Just save whatever scraps you have from cutting up meat. You can use as little as ¼ fat, but the sausage is much, much better if 1/3 is used. Sausage making is one of the most fun of all my projects. But don’t rush through it or it can turn into a nightmare. If you’ve just finished cutting up your pig, give yourself a break and wait until the next day to do the sausage.

I have enclosed several recipes that you might like to try. We like to make many different kinds each year. Whatever you do though, take the time to cook some of each type before you package it or stuff it into casings. It may be too bland or worse too spicy, in which case you’ll have to add more meat.

If sausage is being made from pork, only one grinding will suffice but beef or goat should be ground twice using a coarser grind the first time.

Figure 15.  Cuts of meat from a cowFigure 15. Cuts of meat from a cow

Some recipes call for water and some don’t, but if you’re making link sausage you will have to add some liquid. Add enough so that the sausage is easy to work.

Smoking

Hardwood must be used for smoking so that the meat doesn’t get resins in it, as it would from pine. When smoking hams, bacon and sausage, you use what is called a cool smoke. This means that the meat is not being cooked while it is being smoked. You can use anything to hold the meat and smoke. We built a smokehouse out of sheets of plywood, which enables us to walk inside to hang the meat.

We use an old woodstove to provide the smoke, which passes from the stove through a stovepipe with damper into the smokehouse. The pipe should go in fairly low, but not so low as to inhibit draw. For an hour or so, leave the door ajar to let excess moisture escape. Then close it and try to keep the temperature around 100°. When it’s done is a judgement call, but we give sausage approximately 12 hours, bacon 14, and hams 48. The color is the key. It should be the color of mahogany.


How to butcher a chicken
in 20 minutes or less...

...while leaving the carcass and feathers intact!

By Dr. Roger W. Grim, D.C.


When I was 12 years old Grandpa would let me help him pluck whole chickens after we had dipped them in scalding hot water in a washtub. That was the way he sold whole chickens to stores with his family business.

Figure 1. With a trash bag properly fitted around the chicken, clean up will be easy.
Figure 1. With a trash bag properly fitted around the chicken, clean up will be easy.

One day I asked Grandpa, “Isn’t there an easier way to dress out a chicken?” He showed me a method with no need to pluck feathers and no smelly stench from a wet chicken. It’s just a fast, easy way to put meat on the table.

Things you will need

  1. A sharp knife, axe, meat cleaver, or machetefor cutting off the head.
  2. Rope. Cut 3 or 4 pieces of ¼-inch rope 12 to 18 inches long. One is to tie the chicken’s legs together tightly before you cut the head off; otherwise you will have a headless chicken running about the yard. The other is to tie the chicken’s legs onto your hook on a tree or cart.
  3. A bowl. I use a stainless steel one but any large bowl or panwill do. Put your chicken in it once you cut it away from the carcass.

  4. Figure 2. Front view showing where the cuts are made and how the skin is peeled away
    Figure 2. Front view showing where the cuts are made and how the skin is peeled away

  5. A large bowl of water. Again I use a stainless steel one. It’s to keep my hands and knife clean while skinning the chickens.
  6. I use two sawhorsesfor a table base, over which I placed a sheet of ¾-inch plywood 24 x 48 inches. If you have a small folding table you could use it.
  7. A clean sheet of plastic or butcher’s paper big enough to cover your work table top. Tape it on or tuck it under the table top.
  8. I use my trusty cart, setting it up on end. The handle bar is just the right height for me to hang the chickens from and skin. I put a concrete block in it while I’m pulling the skin downward so the cart will not fall on me.
  9. A garden hose is handy to clean your knives and to pre-clean the chicken of any dirt or feathers before they are taken into the house for final cleaning and freezing preparation.
  10. A large black garbage bag with two twist ties that hold the garbage bag on the cart. Cut the garbage bag two-thirds of the way down so that anything you cut off while skinning, such as the feathers and carcass, goes into the bag (Figure 1).

Figure 3. A view showing how to cut away the mini-wing drumstick
Figure 3. A view showing how to cut away the mini-wing drumstick

The process

Now you are ready to butcher and skin the chicken.

Tie the chicken’s legs together and cut off its head. Then hang the chicken up by its legs (see Figure 2) with the breast of the chicken facing you. Make the first cut around the yellow part of the leg joint only deep enough to separate the skin, but not deep enough to cut the leg tendon.

Cut and pull down the skin from the leg, cutting just deep enough that the skin will come loose from around the meat. Pull the skin of the chicken down laterally to each side, all the time cutting away the other skin to reveal the leg meat that you will cut off later.

Figure 4. The skinned carcass, ready for you to take the meat
Figure 4. The skinned carcass, ready for you to take the meat

Continue to cut and pull the skin all the way down and backwards around the upper thigh. Continue to cut and pull the skin down around the breast and cut the wing loose at the first joint of the wing (Figure 3). Some people may want to continue to clean and cut around the feathers of the wing for the small tip of the wing bones, but for me there is so little meat it is not worth it.

It’s as easy as 1, 2, 3

Now we are ready to strip the skinned carcass (Figure 4).

First, cut the wings, or mini-drumsticks, off at the joint near the breast. By forcing them backwards and cutting as close to the breast and joint as possible, you will expose the wing joint and you can cut through and around it.

Next, cut the breast out. Lay your knife at an angle, starting the cut as close to the breastbone as possible. Take your knife and stay close to the rib cage while cutting downward and backward in an arcing direction as shown in Figure 5. Repeat the process on the other breast.

Figure 5. Side view showing where to cut the meat
Figure 5. Side view showing where to cut the meat

You are ready to claim the legs and thighs all in one piece. If you want to separate them later you can do so. Go up to the ankle joint at about ¾ to 1 inch above the “leggin’s” (that’s what I call the scaly yellow part above the feet on the chicken), and cut through and around the joint so that each leggin’ and foot falls free. While holding the drumstick and thigh in the left hand, take your right hand and hold the carcass while at the same time pushing the thigh and drumstick backwards. This is like opening a set of French doors. You will both see and hear the thigh joint pop loose from the hip joint. Cut as close to the round point as possible (Figure 5).

To separate the thigh from the carcass, make the next and final cut at the back upper part of the thigh, just about 1½ to 2 inches next to the anus. You now have a complete thigh and drumstick.

Some folks might say that you are not getting all the meat, that you are leaving the two small bony pieces on the wing tip, the two little scraps of meat on the backbone, the liver, and the neck. I say if you like those parts, go for it.

Figure 6. The results of a freshly skinned and butchered chicken.
Figure 6. The results of a freshly skinned and butchered chicken.

100+ years in our family

With this method, I have butchered chickens for more than 40 years, just like my grandfather did for 60 years before me. I can remember that Grandma’s chicken fried in a cast iron skillet beat Col. Sanders by a mile.

Raising your own stock, whether it be young chicks to fryer size, rabbits, goats, or beef cattle can be a family affair. Children gain knowledge, learn responsibility, and the necessary basics of self-sufficiency.

Tuesday, December 29, 2009

Mediprep

Christmas Day, 2009, I slipped on a patch of ice on my front porch and twisted my knee pretty severely. Today I finally got to the doctor and the diagnosis (which I had already come up with myself - R.N., remember?) is a sprained medial collateral ligament, possibly with a torn meniscus on top of that. Orders are ibuprofen around the clock until the swelling subsides, rest, ice, compression, and elevation (RICE), wait three weeks and if not significantly better, return for an MRI.


I think it will be fine - well, as fine as it was before, anyway, which isn't great. ("Doctor, will I be able to play the violin....I mean rugby?") But it got me thinking about preparation for medical emergencies. Lately I haven't been writing about it much, but my preparations for a more self-sufficient homestead are proceeding apace. Many of my major goals are either met (reproducing livestock, barns and fences, Homero's shop, biodiesel processor) or partially met (water storage, food storage systems, off-grid heat and cooking capability). Some are still in the planning stage (electricity generation).

Over the past several months I have slowly been building up the pantry, with the goal of eventually having a year's worth of food on hand. It's a gradual thing; an extra twenty pound of rice one week, a case of tuna the next, et cetera. When I hurt myself and it happened to be a holiday weekend with no medical attention short of the emergency room, it occurred to me it would be a good idea to do an inventory of my medical preparedness. One never knows what the future holds, and if it holds scenarios in which professional attention is not readily available (euphemism for "Oh crap, we're goin' down!") then it behooves us all to make what preparations we can.

As in other areas, medical preparedness consists of both knowledge and equipment. Although I am a registered nurse, my training is rapidly receding into the fuzzy past and it would be a good idea for me to take a first aid course. Every adult in a given household should at least have CPR training. Lucky for me I have all my old college nursing textbooks, which make a pretty big stack and include all kinds of extremely useful information. Many used bookstores carry textbooks, and emergency medicine texts should be relatively easy to find. This isn't the forum for a complete course in first aid, but adults should - at a minimum - know how to treat bleeding, recognize anaphylactic shock (extreme allergic reaction), give the heimlich maneuver and CPR.

Building a medicine cabinet is a good idea. We all have a bottle of aspirin in the cupboard, but that doesn't cut it. A good medicine cabinet will have a supply of both equipment and medicines. Here's a list of what's in mine - as a nurse, I have some things that aren't necessary or helpful for the average person, so take with a grain of salt.

Equipment:
Thermometer, band-aids, sterile gauze, tape, moist burn pads, ace bandages, self-adhesive wrap (horse tape), couple of assorted braces (wrist, knee) scissors of various sizes and specialties, good quality tweezers, nail clippers, chemical cold packs (if the power is out, you still want to be able to ice an injury), iodine and alcohol swabs, dental floss, stethoscope, otoscope, blood pressure cuff, blood sugar monitor. Measuring spoons and syringes (no needles). Epi-pen. cotton balls. An eyewash cup.

Medicines:
Not including prescriptions (try to have a month's supply of any prescription meds), aspirin, tylenol, and ibuprofen in quantity, including liquid and pediatric formulations. Benadryl for allergic reactions. Hydrocortisone cream. Triple antibiotic ointment (neosporin, for example). Tums or other antacid. An anti-diarrheal medicine and a laxative. Throat lozenges and spray - I like Chloraseptic, which actually contains an anesthetic. Mouthwash. Iodine. Hydrogen peroxide and rubbing alcohol. Anti-fungal cream for vaginal infections. Nasal spray (good for bites and stings as well as stuffy noses). Epsom salts.

That's about all I can think of at the moment, though I'm sure more will occur to me later. Most of these items can be purchased at a VERY steep discount at Costco. For example, if you buy Ibuprofen in 24 caplet bottles at the grocery store, you will pay about $5.00. If you go to Costco, you can get 500 tablets for about 8 bucks. Same with Benadryl (diphenhydramine is the generic name) and things like band-aids. I think a year's worth of medical supplies is a laudable goal. Not all medications will last a year, but most will. Just keep the cap on that bottle of hydrogen peroxide!

UPDATE: I thought of a couple of items important enough to add. Vitamins and fluoride tablets or drops.


Read more: http://newtofarmlife.blogspot.com/#ixzz0b7roKzPz

Friday, December 25, 2009

12/25/09

First update in some time - the Celexa works so well. I haven't been slacking off, however. I made another major purchase intended to help become self-sufficient long term. For $400 I got a complete beekeeping set up - four fully functional hives (12 drawers), the hive tools, the smoker, the plates, the headdress, some feeders... basically the whole shebang.

One of the hives had live bees in it, but the man said he very much doubted they would survive the winter, so I'll have to start fresh come spring. That gives me plenty of time to read up. I know fuck-all about beekeeping. It's actually Homero who was interested - his dad used to keep bees.

Here are some get-started articles:

BEEKEEPING BASICS

Bees have been managed for their honey production for about 5000 years or so. Especially for the smallholder, beekeeping can be an interesting and rewarding pursuit. They are not labor intensive and don’t take up much space. To top it off, the rewards are sweet, literally.

The honey that an average colony will produce in a year is usually enough for a family to use with enough left over to sell some as well. The market for good wildflower honey is always good, and selling or bartering your surplus can be a welcome shot in the arm to the homestead economy. Even after a fairly hard winter and an average summer, I have had a colony of bees produce a surplus of honey with a total extracted weight of 110 pounds. That was much more sweetener than we use in a year, so we were able to realize a little extra income from the surplus.

Illustration of a beehive and its components
Illustration of a beehive and its components

The hive

To get started, you will need some basic equipment for the hive itself. You will need and want to add items as you become more familiar with beekeeping. To help you, take a look at the accompanying glossary and become familiar with the basic parts of the beehive and some of the beekeeper’s terminology.

Next, you will need to obtain the basic parts of the hive as depicted in the illustrations. This is best done initially by purchasing the pieces you need. Nearly all of the bee equipment suppliers offer beginner’s packages that have just about everything you’ll need. Check out some of the sources listed at the end of this article and get their catalogs. You may also be fortunate enough to locate and purchase working colonies of bees from an established beekeeper.

Once you have your hive hardware, you will need to get it situated. You will need to have the hives elevated somewhat, as shown in the accompanying illustration, and not just resting on the ground. You can set them on some concrete blocks, a wooden stand made especially for the purpose, or another structure that will get them up out of the grass.

The illustration depicts the basic make up of a typical beehive. Most texts describe the use of shallow honey supers (see the glossary) atop the deep hive bodies, but I use the same size deep supers or hive bodies throughout. The deep super and hive body are the same size; the only difference is in their name, being given for their particular use on the hive. The reason I like using the deep supers is that I have to purchase only one size of foundation and I can make or purchase the boxes all the same size as well. The main drawback to using deep supers is that they can weigh up to 100 pounds when full. However, there is less handling, overall, than when using shallow supers and the bees work the deep supers well.

Another trick is to use only 9 frames in the standard 10-frame super. By evenly spacing the frames in the super, the bees will naturally draw the comb out further. This will put the cappings up higher above the edge of the frame and help to make the uncapping chore much easier. (More on this later.) You can easily make or purchase a spacer to help to insure getting the correct spacing on the frames in the super although spacing them by hand in just a few colonies is not a difficult chore.

The veil and helmet is another basic piece of beekeeping gear.
The veil and helmet is another basic piece of beekeeping gear.

Speaking of frames, these very essential and basic pieces of equipment are the heart of the home apiary. They allow quick and easy access for examining the bees and for removal of honey. They will need to be set up with wired foundation. These are sheets of beeswax with two important features: first, they have embedded wires that help to support the comb and prevent it from tearing when extracting honey. Second, it is embossed with the exact shape of the honeycomb that will be drawn out on it. The result is nice, uniform combs.

Where do I get my bees?

Once you have the basic hardware in place, you need to acquire your winged livestock for the hive. Probably the best way for beginning beekeepers to get bees is to purchase them from a commercial supplier. Some of the beekeeping suppliers listed at the end of this article offer bees for sale. Your honeybees will be mailed to you (yep, mailed) in a screen-sided wooden box. You can count on getting an early call from the post office to let you know that your bees have arrived. Somehow, having 10,000 or so buzzing bees in their work area tends to make postal employees nervous.

Installing package bees

A bee brush can be used to gently move bees aside to examine the combs for honey and brood production.
A bee brush can be used to gently move bees aside to examine the combs for honey and brood production.
Bee gloves often have long gauntlets attached to help keep honey bees off the arms.
Bee gloves often have long gauntlets attached to help keep honey bees off the arms.
he metal hive tool is used to pry hive bodies apart, remove and scrape frames, and lift top covers.
The metal hive tool is used to pry hive bodies apart, remove and scrape frames, and lift top covers.

Once you get your package of bees home, first give them some sugar syrup. They will very likely have exhausted the supply sent with them on their postal journey and will need nourishment. This is done simply by making a simple syrup by adding two cups of sugar to one cup of boiling water. Mix it thoroughly and allow it to cool. Then just use a small paintbrush to paint it onto the wire sides of the cage. The bees will take all they can get, but don’t soak them. As they load up on food, it also helps to calm them. Actually putting the bees in the hive should be done in the late afternoon or evening so that they are less likely to vacate the hive. If necessary, you can keep the package of bees in a cool, dark place until that time.

Your hive should be set up and ready to accept the new residents. You should have a bottom board on a solid base, a hive body and the hive covers ready. Have only enough frames—five or six-with foundation in the hive body. Have the remaining frames alongside and available to use in a bit.

Don your veil and gloves and give the package a dose of sugar syrup with the brush. Open the package and remove the tin feeder can.

The queen bee will be in a small cage that is suspended inside the top of the package. Locate the cage and take it out along with any bees hanging onto it. Close the package so other bees don’t escape. You will see that the queen cage has a small cardboard or cork stopper in one end. This plug covers the escape hole. Remove that stopper and place the queen cage and any hangers-on at the top and between the two frames that will be nearest the center of the hive. Gently wedge the queen cage between the top bars of the frames. Beneath the cork stopper, the queen cage contains a small plug of sugar that the bees will quickly remove to allow the queen to escape into the hive.

You should have your smoker handy. The smoker is a basic piece of bee equipment and consists of a combustion chamber, a bellows, and a funnel. The combustion chamber provides the place to burn the material with which the smoke is created. Try to get old, but clean, burlap for this purpose. Burlap ignites easily yet smolders well, which is exactly what is needed. Some folks use corncobs as fuel, but I cannot personally vouch for the effectiveness of them. Whatever fuel you use, be sure it is clean, preferably of a natural fiber or material, and does not give off any noxious fumes, harmful to you or your bees. The bellows on a smoker serve to help keep the fuel lit, and to provide the puffs of the smoke needed to work the hive. The funnel simply concentrates the smoke and directs it to where it is needed.

When first working your hive, use the smoker as you begin. First, give a few good puffs of smoke directly into the hive entrance. Then, lift the top cover and inner cover, and apply several good puffs of smoke into the super. The whole idea is to make the bees think that their hive is about to “go up in smoke.” Instinctively, the bees will load up on honey and be prepared to evacuate the hive if necessary. Bees that are so loaded are not nearly as likely to sting than if we would just go up, pull off the top cover and start pulling out frames. When smoking the hive, take care not to puff the smoker so much or so hard as to create very hot smoke or actual flames. That will certainly kill any bees it comes close to, or will singe their wings at least. The idea is to create the cool smoke needed to calm the bees down and preoccupy them with the thought of the impending danger of fire.

This illustration depicts one of the removeable frames with foundation installed.
This illustration depicts one of the removeable frames with foundation installed.

Give the package of bees a gentle puff of smoke. Pick up the package and remove the closure. Gently shake a big handful-sized bunch of bees right over and onto the queen cage. Then shake the rest of the bees out and into the space where you have taken the frames out of the hive body. They will quickly seek the cover and relative darkness of the frames and will join the rest of the bees. Place the open package that will likely contain some stragglers, near the entrance of the hive so that the remaining bees can easily enter. Gently replace the remaining frames of foundation in the hive body and set the inner cover in place. Insert a feeder at the hive entrance or inside an empty hive body on top of the inner cover. Feed the same simple syrup recipe you prepared when they arrived. You can check the bees in a about a week. In that week, the queen will begin laying eggs and the bees will settle down, starting to work. Once the bees start to get acclimated to their new surroundings and begin to work the various nectar sources, you can cease feeding them. Remove the feeder and extra hive body if used, and replace the top cover directly upon the inner cover.

Working your bees

Although they can pretty well be left alone to do their work, your bee colonies will need to be checked periodically. When working around your bees, it is a good idea to wear light colored clothing or coveralls. They seem to get less excited when you do so. Using your veil, smoker, and hive tool work calmly and steadily around your hives and you should have no problems.

With the top and inner cover removed, use your hive tool to lift a few frames out to examine them. Is the comb fully drawn out? Are the combs being filled with honey? Are the combs capped off and ready to extract honey from? Do the bees appear lively and healthy? After checking your colony, merely replace the inner and top covers. The bees will fan and clear the hive of any remaining smoke and life in the colony will soon be back to normal.

Reaping the harvest—taking off honey

When you have checked your hives, and find supers full of capped honeycomb, it is time to remove your honey crop. When taking off honey, you must first remove the bees from the honey super.

The best method that I have found is to use the commercial product called Bee-Go. This product is a chemical solution called butyric anhydride. It is applied to a purchased or easily made “fume board” and put atop the hive in the place of the top cover and inner cover. One way to make a fume board is to simply use an old or extra hive cover. Staple a layer or two of ordinary burlap to the underside. It will act as the absorbent pad to which you will apply the chemical.

The bees simply do not like the odors given off by the chemical and head further down into the hive. Normally, within a couple of minutes, nearly every bee has hightailed out of the honey super. With the use of shallow supers, you can probably clear a couple of supers at a time. Since I normally use deep honey supers I can remove one cleared super and replace the fume board atop the next to get it cleared out as well.

The smoker is an essential and basic part of beekeeping equipment.
The smoker is an essential and basic part of beekeeping equipment.

Another chemical bee-mover is one that I have not tried personally, but have read that it is good stuff. Called Fischer’s Bee-Quick, this product is a blend of natural oils and herbal extracts with a sweet, almost almond smell. This product should hold promise for the home beekeeper. Like Bee-Go, it is used in combination with a fume board to clear the honey supers.

Apply the Bee-Go or Bee-Quick to the underside of the fume board as directed on the container. Place it atop the hive and wait for a few minutes for the bees to move down. If you have several supers to remove, take off the first cleared super, and replace the fume board to continue to move the bees downward.

Extracting honey

It is very difficult to extract honey without the use of a mechanical extractor. If you are not using specially designed frames from which you will take sections of comb honey (honey marketed with the honey comb intact), then you simply will need to have access to one of the centrifugal type extractors. They are available in many sizes, including ones suitable for the small place. They can be built at home, but I have had better luck using a manufactured model. These machines are not cheap, starting out in the $200 to $300-range. If you know some other beekeepers, consider pooling your money and purchasing an extractor, with each of you using it as needed.

Now that you have your full supers waiting, you will need to remove the wax caps on the combs. As each cell in the honeycomb is filled, the bees seal it with beeswax. These cappings must be removed to extract the honey inside the comb. This is done by using long heated knives. Some folks use two or three long blades such as bread knives. Keep the blades immersed in a pot of very hot water and use the hot knives to slice the cappings from the frame. As one knife cools, put it into the hot water and use another heated one. Slice off the cappings and let them drop into a pot or kettle. A lot of honey will drain from the cappings, and the wax is a valuable by-product.

You may also use a special electrically heated knife to remove the cappings from the honey-laden frames. This knife is available from any good bee supply house and simply uses an electrical element to heat the hollow blade. It is used in the same way as a regular knife, using a smooth back and forth motion to slice the cappings from the comb.

Place the decapped frames into the extractor with the top bar facing outward. This is important to extract all the honey. Honeycomb is actually built by the bees with the individual cells sloping very slightly downward towards the center of the frame. By placing the top bar of the frame outward, you will be able to sling virtually all the honey out of the comb.

Some small home-sized extractors sometimes have the frames facing flat side outward. Once some of the honey is spun out of the one side, the frames are rotated and honey is taken from the other side. Then they are reversed once more and the extraction is completed. The reason for all this is to prevent the weight of the honey on the inside of the frame from causing the foundation to pull loose as the extractor is spun and the honey is taken from the outside comb.

Attendant bees cluster around a queen.
Attendant bees cluster around a queen.

As your honey is extracted from the comb, take the empty frames and replace them in the super. Allow the honey to accumulate in the bottom of the extractor and then drain it off. You should plan to run it through a few layers of cheesecloth to remove any bits of wax, pollen, or bees. Then, simply decant it into the containers of your choice. I have used purchased honey jars with printed labels and I have used quart and pint canning jars with hand printed labels. You will have no trouble selling all the honey you want to sell, regardless of the type of jar it comes in.

After extracting the honey from your supers, they will need to be cleaned up for winter storage. I usually allow the bees to work on that chore. I take the extracted supers and set them out and allow the bees to finish cleaning up any honey that might remain in the frames. After allowing a day or two for the frames to be cleaned up, each super is examined for damage, rot, or other need of repair. The frames, too, are looked at to see if any are in need of replacement. Any remaining deposits of spur comb and propolis (bee glue) are removed by scraping with the hive tool.

Next, I bag each super, frames and all, in a large plastic bag—the 50-gallon lawn-size bags work well. I then place each super in the deep-freeze for about a week—long enough to kill any wax moths, eggs, or larvae. Then the supers are placed away, still bagged, to be used again next year.

This article certainly cannot cover all the interesting aspects of beekeeping. I do hope that it will motivate you. Once you get going, you may want to expand to several colonies, make all or part of your beekeeping equipment, or otherwise get more into this, the “gentle art of beekeeping.”

Glossary of terms

Bee brush: A soft brush or whisk (or handful of grass) used to remove bees from frames.

Beehive: A box or receptacle with movable frames, used for housing a colony of bees.

Bee space: A space big enough to permit free passage for a bee but too small to encourage comb building, and too large to induce propolizing activities; measures 5/16 to 3/8 inch.

Bee suit: A pair of coveralls, usually white, made for beekeepers to protect them from stings and keep their clothes clean; some come equipped with zip-on veils.

Bee tree: A tree with one or more hollows occupied by a colony of bees.

Bee veil: A cloth or wire netting for protecting the beekeeper’s head and neck from stings. Most often attached to a hat or helmet.

Beeswax: 1. A substance that is secreted by bees by special glands on the underside of the abdomen, deposited as thin scales, and used after mastication and mixture with the secretion of the salivary glands for constructing the honeycomb. Its melting point is from 143.6 to 147.2 degrees F. 2. a wax obtained as a yellow to brown solid by melting a honeycomb with boiling water, straining, and cooling and used especially in polishes, modeling, and making patterns.

Bottom board: The floor of a bee hive.

Brood: Immature stages of bees not yet emerged from their cells; the stages are egg, larvae, pupae.

Brood chamber: The part of the hive in which the brood is reared; may include one or more hive bodies and the combs within. Also called a ‘brood box.’

Brood nest: The part of the hive interior in which brood is reared; usually the two bottom supers. Sometimes called the “hive body.”

Cappings: The thin wax covering over honey; once cut off of extracting frames they are referred to as cappings and are a source of premium beeswax.

Cell: The hexagonal compartment of a honey comb.

Colony: The aggregate of worker bees, drones, queen, and developing brood living together as a family unit in a hive or other dwelling

Comb: The wax portion of a colony in which eggs are laid, and honey and pollen are stored.

Comb, drawn: Wax foundation with the cell walls drawn out by the bees, completing the comb.

Comb foundation: A commercially made structure consisting of thin sheets of beeswax with the cell bases of worker cells embossed on both sides in the same manner as they are produced naturally by honey bees.

Comb honey: Honey in the wax combs, usually produced and sold as a separate unit, such as a wooden section 4½-inch square, or a plastic round ring.

Drone: The male honeybee which comes from an unfertilized egg (and is therefore haploid) laid by a queen.

Extracted honey: Honey removed from combs by means of a centrifugal force; the combs remain intact.

Feeder: A jar used to supply sugar syrup to bees as a supplemental source of food. Feeders may be purchased that are attached to the front of the hive with the opening inserted into the hive opening, or may be devised by using quart or gallon jars with several very small holes punched into the lid. The filled jar is inverted and placed over the opening in the inner cover, inside an empty hive box and the hive cover placed over that.

Foundation wax: Thin sheets of beeswax embossed or stamped with the base of a worker cell on which bees will construct a complete comb (called drawn comb); also referred to as comb foundation, it comes wired or unwired.

Foundation, wired: Comb foundation which includes evenly-spaced vertical wires for added support; used in brood or extracting frames.

Frame: Four pieces of wood forming a rectangle, designed to hold honey comb, consisting of a top bar, two end bars, and a bottom bar (one or two pieces); usually spaced a bee-space apart in the super.

Gloves: Leather, cloth, or rubber gloves worn while inspecting bees.

Guard bees: Worker bees about three weeks old, which have their maximum amount of alarm pheromone and venom; they challenge all incoming bees and other intruders.

Hive: A manmade home for bees including a bottom board, hive bodies, frames enclosing honey combs, and covers.

Hive body: A wooden box containing frames.

Hive stand: A structure serving as a base support for a beehive; it helps in extending the life of the bottom board by keeping it off damp ground.

Hive staples: Large C-shaped metal nails, hammered into the wooden hive parts to secure bottom to supers, and supers to super before moving a colony.

Hive tool: A flat metal device with a curved scraping surface at one end and a flat blade at the other; used to open hives, pry apart, and scrape frames.

Honey extractor: A machine which removes honey from the cells of comb by centrifugal force. Smaller, hand-cranked machines are available for small home-sized operations.

Honey supers: Refers to hive bodies used for honey production.

Inner cover: An insulating cover fitting on top of the top super but underneath the outer cover, with an oblong hand hole in the center.

Outer cover: The last cover that fits over a hive to protect it from rain; the two most common kinds are telescoping and migratory covers.

Package bees: A quantity of adult bees (2 to 5 pounds), with or without a queen, contained in a screened shipping cage.

Propolis: The very sticky substance secreted by honeybees used to close and seal small spaces. Also referred to as ‘bee glue.’

Queen: A fully developed mated female bee responsible for all the egg laying of a colony; recognized by other bees by her special pheromones (odors).

Queen cage: A special cage in which queens are shipped and/or introduced to a colony, usually with 5 or 6 young workers called attendants, and a candy plug.

Queen cage: candy: Candy made by kneading powdered sugar with invert sugar syrup until it forms a stiff dough; used as food in queen cages.

Queen excluder: A device made of wire, wood or zinc (or any combination thereof) having openings of .163 to .164 inch, which permits workers to pass but excludes queens and drones; used to confine the queen to a specific part of the hive, usually the brood nest.

Radial extractor: A centrifugal force machine to throw out honey but leave the combs intact; the frames are placed like spokes of a wheel, top bars towards the wall, to take advantage of the upward slope of the cells.

Smoker: A metal container with attached bellows which burns organic fuels to generate smoke; used to control aggressive behavior of bees during colony inspections.

Spur comb: Small deposits of comb built throughout the hive to close down large spaces or holes to a proper ‘bee space.’

Sugar syrup: Feed for bees, containing sucrose or table (cane) sugar and hot water in various ratios.

Super: A receptacle in which bees store honey; usually placed over or above the brood nest; so called brood supers contain brood.

Supering: The process of placing honey supers on a colony in preparation for a honey flow.

Swarm: A collection of bees, containing at least one queen that split apart from the mother colony to establish a new one; a natural method of propagation of honey bees.

Uncapping knife: A knife used to shave off the cappings of sealed honey prior to extraction; hot water, steam, or electricity can heat the knives.

Veil: A protective netting that covers the face and neck; allows ventilation, easy movement, and good vision.

Worker bees: Infertile female bee whose reproductive organs are only partially developed, responsible for carrying out all the routine of the colony.


Saturday, November 28, 2009

some new stuff for the homestead

IMG_0005.JPG.jpg

Craigslist has been good to me lately. Last week I found some items I've been looking for for quite some time. These big white cubes are 250 gallon food-grade plastic tanks. They have steel cages around them so they can be stacked, and you can screw them together so they make one 500 gallon tank (et cetera). They also have spigots on the front so water can be drained easily. These are not easy to find; they show up rarely on Craigslist, and often are unusable because they have been used to store something noxious or else they are very expensive. I lucked out; I found a guy who had 8 of them. He was selling them for $100 a piece - already a good price - but when I offered $700 for all of them he accepted. Also he took $50 to deliver them, which I thought was extremely reasonable. These particular tanks were used to store soy lecithin, which is a food additive naturally derived from soybeans. It's completely harmless unless you are allergic to soy. I'll obviously be washing them out with a high pressure hose before I use them to store water.

I know. It's been raining here for weeks on end, sometimes torrentially. The idea that I might need to store seems totally ridiculous. It always does this time of year. But all I have to do is think back to last August. Anyway, these are for the future. Do I think I will enjoy unmetered water forever? No, I do not.

Actually, I only get five of them for water storage. Homero gets the other three for use in his biodiesel production.

This is my other find. I've been wanting a woodstove for a long time. Currently our only heat is propane, and that is not sustainable long term. Also I don't have any way to cook in the event of a power outage, and I'd like to have one. A woodstove fulfills both these purposes. It's a little rusty, but I can clean that up and paint it with the special woodstove paint. It's been sitting in some guy's garage for about ten years and now he's tearing down the garage. He says it was in perfect working order when he put it out there. It only cost me a hundred bucks, so I can't go too far wrong. The only question is where and how to install it. But that is for another day. Getting it into a pickup, hauling it home, and getting it out of a pickup and into the playroom was enough work for one day.

These are small steps - they are only purchases at this point. All I've done so far is shop. Getting the tanks hooked up and made into a functioning rainwater catchment system will be a job. Ditto installing the woodstove. Recently I purchased a handgun, with an eye to butchering. That's still just a purchase too - I haven't fired it yet, much less used it to butcher a goat or a pig. But gathering materials is the first step of any endeavor, right? You can't make an omelet until you have some eggs.


Read more: http://newtofarmlife.blogspot.com/#ixzz0YDqzCkOF

Sunday, November 8, 2009

11/8/09

Update on self-sufficiency:

I think I have taken some pretty big strides since last I posted here. I have helped butcher a deer (roadkill, and we didn't eat it, but it was good practice) and now feel prepared to butcher our first goats in a few weeks.

To that end, I have bought a handgun and am taking a safety and training course next week. It's a ruger single action .22 revolver. Nice cheap ammunition and very reliable. I don't look forward to killing goats, but I do look forward to becoming a proficient shooter. I used to be a pretty shot with a daisy air rifle... for a nine year old.

The house is getting all new insulation in the attic and crawlspace in the next couple of weeks.

I went ahead and told my money manager that I planned on spending $50,000 or more in the next five years and why. Felt like an idiot but he was very professional.

I think I'm going to buy a 2000 gallon water tank. It's on sale for $300 which is absurdly cheap (good brand, UV protected against algae, shipped to my house) and get set up on the rainwater catchment. Right now it's been raining for weeks and there are standing ponds all over the place and the idea of needing to conserve water feels ridiculous, but all I have to do is think back to last august. It was a dust bowl here. It would be nice to know we had water for the garden.

We've been running straight biodiesel in our two cars for quite a while now. All we need to do to keep that up is maintain good relations with our neighbors who give us oil. It's time to pay them a call with eggs in hand.

All in all, I feel pretty good.

Oh yeah, I also learned just how incredibly easy it is to make decent apple beer (or tepache, in Mexican vernacular). As much as anything else, knowing I'll have access to good cheer makes me feel secure.


Friday, October 23, 2009

100 ways to prepare - seasonal, positive, simple

100 Things You Can Do to Get Ready for Peak Oil

Sharon February 22nd, 2008

SPRING

  1. Rethink your seed starting regimen. How will you do it without potting soil, grow lights and warming mats. Consider creating manure heated hotbeds, using your own compost, building a greenhouse, or coldframe, direct seeding early versions of transplanted crops, etc…
  2. Your local feed store has chicks right now – even suburbanites might consider ordering a few bantam hens and keeping them as exotic birds. Worth a shot, no? You can grow some feed in your garden for Them, as well as enjoying the eggs.
  3. Order enough seeds for three years of gardening. If by next spring, we are all unable to get replacement seed, will you have produced everything you need? What if you can’t grow for a year because of some crisis? Order extras from places with cheap seed like www.fedcoseeds.com, www.superseeds.com, www.rareseed.com.
  4. Yard sale season will begin soon in the warmer parts of the country, and auctions are picking up now in the North. Stocking up on things like shoes, extra coats, kids clothing in larger sizes, hand tools, garden equipment is simply prudent – and can save a lot Of money.
  5. The real estate “season” will begin shortly, with families wanting to get settled in new homes during the summer, before the school year starts. If you are planning on buying or selling this year, now is the time to research the market, new locations, find that country property or the urban duplex with a big yard.
  6. Once pastures are flush, last year’s hay is usually a bargain, and many farmers clean out their barns. Manure and old hay are great soil builders for anyone.
  7. Check out your local animal shelter and adopt a dog or cat for rodent control, protection and friendship during peak oil.
  8. As things green up, begin to identify and use local wild edibles. Eat your lawn’s dandilions, your daylily shoots, new nettles. Hunt for morels (learn what you are doing first!!) and wild onions. Get in the habit of seeing what food there is to be had everywhere you go.
  9. Set up rainbarrel or cistern systems and start harvesting your precipitation.
  10. Planning to only grow vegetables? Truly sustainable gardens include a lot of pretty flowers, which have value as medicinals, dye and fiber plants, seasoning herbs, and natural cleaners and pest repellants. Instead of giving up ornamentals altogether, grow a garden full of daylilies, lady’s mantle, dye hollyhocks and coreopsis, foxgloves, soapwart, bayberry, hip roses, bee balm and other useful beauties.
  11. Get a garden in somewhere around you – campaign to turn open space into a community garden, ask if you can use a friend’s backyard, get your company or church, synagogue, mosque or school to grow a garden for the poor. Every garden and experienced gardener we have is a potential hedge against the disaster.
  12. Join a CSA if you don’t garden, and get practice cooking and eating a local diet in season.
  13. Eggs and greens are at their best in spring – dehydrated greens and cooked eggshells, ground up together add calcium and a host of other nutrients to flour, and you won’t taste them. We’re not going to be able to afford to waste food in the future, so get out of the habit now.
  14. Make rhubarb, parsnip or dandelion wine for later consumption.
  15. Now that warmer weather is here, start walking for more of your daily Needs. Even a four or five mile walk is quite reasonable for most healthy People.
  16. Start a compost pile, or begin worm composting. Everyone can and should compost. Even apartment dwellers can keep worms or a compost Bin and use the product as potting soil.
  17. Use spring holidays and feasts as a chance to bring up peak oil with friends and family. Freedom and rebirth are an excellent subjects To lead into the Long Emergency.
  18. Store the components of some traditional spring holiday foods, so that in hard times your family can maintain its traditions and celebrations.
  19. With the renewal of the building season, now is the time to scavenge free building materials, like cinder blocks, old windows and scrap wood – with permission, of course.
  20. Try and adapt to the spring weather early – get outside, turn down your heat or bank your fires, cut down on your fuel consumption as though you had no choice. Put on those sweaters one more time.
  21. Shepherds are flush with wool – now is the time to buy some fleece and start spinning! Drop spindles are easy to make and cheap to use. Check out www.learntospin.com
  22. Take a hard look back over the last winter – if you had had to survive on what you grew and stored last year, would you have made it? Early spring was famously the “starving time” when stores ran out and everyone was hungry. Remember, when you plan your food Needs that not much produces early in spring, and in northern climates, A winter’s worth of food must last until May or June.
  23. Trade cuttings and divisions, seeds and seedlings with your neighbors. Learn what’s out there in your community, and sneak some useful plants into your neighbors’ garden.
  24. If you’ve got a nearby college, consider scavenging the dorm Dumpsters. College students often leave astounding amounts of Stuff behind including excellent books, clothes, furniture, etc…
  25. Say a schecheyanu, a blessing, or a prayer. Or simply be grateful for a series of coincidences that permit us to be here, in this place, as the world and the seasons come to life again. Try to make sure that this year, this time, you will take more joy in what you have, and prepare a bit better to soften the blow that is about to fall.

SUMMER

  1. If you don’t can or dehydrate, now is the time to learn. In most climates, you can waterbath can or dehydrate with a minimum of purchased materials, and produce is abundant and cheap. If you don’t garden, check out your local farmstand for day-old produce or your farmer’s market at the end of the day – they are likely to have large quantities they are anxious to get rid of. Wild fruits are also in abundance, or will be.
  2. Consider dehydrating outer leaves of broccoli, cabbage, etc…, and grinding the dried mixture. It can be added to flours to increase the nutritional value of your bread.
  3. Buy hay in the summer, rather than gradually over the winter. Now is an excellent time to put up simple shelters for hay storage, to avoid high early spring and winter prices.
  4. Firewood, woodstoves and heating materials are at their Cheapest right now. Invest now for winter. The same is true Insulating materials.
  5. Back to School Planning is a great time to reconsider transportation in light of peak oil. Can your children walk? Bike? If they cannot do either for reasons of safety (rather than distance) could an adult do so with them? Could you hire a local teenager to take them to school on foot or by wheel? Can you find ways to carpool, if you must drive? Grownups can do this too.
  6. Also when getting ready to go back to school, consider the environmental impact of your scheduling and activities – are there ways to minimize driving/eating out/equipment costs/fuel consumption? Could your family do less in formal “activities” and more in family work?
  7. Consider either home schooling or engaging in supplemental home Education. Your kids may need a large number of skills not provided By local public schools, and a critical perspective that they certainly Won‘t learn in an institutional setting. Teach them.
  8. Try and minimize air conditioning and electrical use during high Summer. Take cool showers or baths, use ice packs, reserve activity When possible for early am or evening. Rise at 4 am and get much of Your work done then.
  9. Consider adding a solar powered attic fan, available from Real Goods www.realgoods.com.
  10. Don’t go on vacation. Spend your energy and money making your home A paradise instead. Throw a barbecue, a party or an open house, and invite The neighbors in. Get to know them.
  11. Be prepared for summer blackouts, some quite extensive. Have Emergency supplies and lighting at hand.
  12. Practice living, cooking and camping outside, so that you will Be comfortable doing so if necessary. Everyone in the family can Learn basic outdoors person skills.
  13. Make your own summer camp. Instead of sending kids to soccer Camp, create an at-home skills camp that helps prepare people for Peak oil. Invite the neighbor kids to join you. Have a blast!
  14. Begin adapting herbs and other potted plants to indoor culture. Consider adding small tropicals – figs, lemons, oranges, even bananas can often be grown in cold climate homes. Obviously, if you live in a warm climate well, be prepared for some jealousy from the rest of us come February ;-) .
  15. Plant a fall garden in high summer – peas, broccoli, kale, lettuces, Beets, carrots, turnips, etc… All of the above will last well into early Winter in even the harshest climates, and with proper techniques or In milder areas, will provide you with fresh food all year long
  16. Put up a new clothesline! Consider hand washing clothes outside, Since everyone will probably enjoy getting wet (and cool) anyhow.
  17. If you have access to safe waters, go fishing. Get some practice, and Learn a new skill.
  18. Encourage pick-up games at your house. Post-peak, children will Need to know how to entertain themselves.
  19. For teens, encourage them to develop their own home businesses over The summers. Whether doing labor or creating a product, you may rely On them eventually to help support the family. Or have them clean out Your closets and attic and help you reorganize. Let them sell the stuff.
  20. Buy a hand pushed lawn mower if you have less than 1 acre of grass. New ones are easy to push and pleasant, and will save you energy and that Unpleasant gas smell.
  21. Keep an eye out for unharvested fruits and nuts – many suburban and rural Areas have berry and fruit bushes that no one harvests. Take advantage and Put up the fruit.
  22. Practice extreme water conservation during the summer. Mulch to reduce The need for irrigation. Bathe less often and with less water. Reduce clothes Washing when possible.
  23. This is an excellent time to toilet train children – they can run around naked If necessary and accidents will do no harm. Try and get them out of diapers now, Before winter.
  24. Consider replacing lawns with something that doesn’t have to be mown – Ground covers like vetch, moss, even edibles like wintergreen or lingonberry, Chamomile or mint.
  25. If it is summer time, then the living is probably easy. Take some time To enjoy it – to picnic, to celebrate democracy (and try and bring one about ;-) , To explore your own area, walk in the nearby woods.

FALL

  1. Simple, cheap insulating strategies (window quilts and blankets, draft stoppers, etc…) are easily made from cheap or free materials – goodwill, for example, often has jeans, tshirts and shrunken wool sweaters, of quality too poor to sell, that can be used for quilting material and batting. They are available where I am for a nominal price, and I’ve heard of getting them free.
  2. Stock up for winter as though the hard times will begin this year. Besides dried and canned foods, don’t forget root cellarable and storable local produce, and season extension (cold frames, greenhouses, etc…) techniques for fresh food when you make your food inventory.
  3. Thanksgiving sales tend to be when supermarkets offer the cheapest deals on excellent supplements to food storage, like shortening, canned pumpkin, spices, etc… I’ve also heard of stores given turkeys away free with grocery purchases - turkeys can then be cooked, canned and stored. Don’t forget to throw in storable ingredients for your family’s holiday staples – in hard times, any kind of celebration or continuity is appreciated.
  4. Go leaf rustling for your garden and compost pile. If you Happen into places where people leave their leaves out for Pickup, grab the bags and set them to composting or mulching Your own garden.
  5. Plant a last crop of over wintering spinach, and enjoy in The fall and again in spring.
  6. Or consider planting a bed of winter wheat. Chickens can Even graze it lightly in the fall, and it will be ready to harvest in Time to use the bed for your fall garden. Even a small bed will Make quite a bit of fresh, delicious bread.
  7. Hit those last yard sales, or back to school sales and buy a few extra clothes (or cloth to make them) for growing children and extra shoes for everyone. They will be welcome in storage, particularly if prices rise because of trade issues or inflation.
  8. The best time to expand your garden is now – till or mulch and let sod rot over the winter. Add soil amendments, manure, Compost and lime.
  9. Now is an excellent time to start the 100 mile diet in most locales – Stores and farms and markets are bursting with delicious local produce And products. Eat local and learn new recipes.
  10. Rose hip season is coming – most food storage items are low in accessible vitamin C. Harvest wild or tame unsprayed rose hips, and dry them for tea to ensure long-term good health. Rose hips are Delicious mixed with raspberry leaves and lemon balm.
  11. Discounts on alcohol are common between Halloween and Christmas – this is an excellent time to stock up on booze for personal, medicinal, trade or cooking. Pick up some vanilla beans as well, and make your own vanilla out of that cheap vodka.
  12. Gardening equipment, and things like rainbarrels go on sale in the late summer/early fall. And nurseries often are trying to rid themselves of perennial plants – including edibles and medicinals. It isn’t too late to plant them in most parts of the country, although some care is needed in purchasing for things that have become rootbound.
  13. Local honey will be at its cheapest now – now is the time to stock up. Consider making friends with the beekeeper, and perhaps Taking lessons yourself.
  14. Fall is the cheapest time to buy livestock, either to keep or for butchering. Many 4Hers, and those who simply don’t want to keep excess animals over the winter are anxious to find buyers now. In many cases, at auction, I see animals selling for much less than the meat you can expect to obtain from their carcass is worth.
  15. Most cold climate housing has or could have a “cold room/area” – a space that is kept cool enough during the fall and winter to dispense with the necessity of a refrigerator, but that doesn’t freeze. If you have separate fridge and freezer, consider disconnecting your fridge during the cooler weather to save utility costs and conserve energy. You can build a cool room by building in a closet with a window, and Insulating it with Styrofoam panels
  16. Now is a great time to build community (and get stuff done) by instituting a local “work bee” – invite neighbors and friends to come help either with a project for your household, or to share in some good deed for another community member. Provide food, drink, tools and get to work on whatever it is (building, harvesting, quilting, knitting – the sky is the limit), and at the same time strengthen your community. Make sure that next time, the work benefits a different neighbor or community member.
  17. Most local charities get the majority of their donations between now and December. Consider dividing your charitable donations so that they are made year round, but adding extra volunteer hours to help your group handle the demands on them in the fall.
  18. Many medicinal and culinary herbs are at their peak now. Consider learning about them and drying some for winter use.
  19. If there is a gleaning program near you (either for charity or personal use) consider joining. If not, start one. Considerable amounts of food are wasted in the harvesting process, and you can either add to your storage or benefit your local shelters and food pantries.
  20. Dig out those down comforters, extra blankets, hats with the earflaps, flannel jammies, etc… You don’t need heat in your sleeping areas – just warm clothes and blankets.
  21. Learn a skill that can be done in the dark or by candlelight, while sitting with others in front of a heat source. Knitting, crocheting, whittling, rug braiding, etc… can all be done mostly by touch with little light, and are suitable for companionable evenings. In addition, learn to sing, play instruments, recite memorized speeches and poetry, etc… as something to do on dark winter evenings.
  22. While I wouldn’t expect deer or turkey hunting to be a major food source in coming times (I would expect large game to be driven back to near-extinction pretty quickly), it is worth having those skills, and also the skills necessary to catch the less commonly caught small game, like rabbits, squirrel, etc…
  23. Use a solar cooker or parabolic solar cooker whenever possible To prepare food. Or eat cool salads and raw foods. Not only won’t You heat up the house, but you’ll save energy.
  24. A majority of children are born in the summer Early fall, which suggests that some of us are doing more than Keeping warm ;-) . Now is a good time to get one’s birth Control updated ;-) .
  25. Celebrate the harvest – this is a time of luxury and plenty, and should be treated as such and enjoyed that way. Cook, drink, eat, talk, sing, pray, dance, laugh, invite guests. Winter is long and comes soon enough. Celebrate!

WINTER

  1. Your local adult education program almost certainly has something useful to teach you – woodworking, crocheting, music training, horseback riding, CPR, herbalism, vegetarian cookery… take advantage of people who want to teach their skills
  2. Get serious about land use planning – even if you live in a suburban neighborhood, you can find ways to optimize your land to produce the most food, fuel and barterables. Sit down and think hard about what you can do to make your land and your life more sustainable in the coming year.
  3. The Winter Lull is an excellent time to get involved in public affairs. No matter how cynical you tend to be, nothing ever changed without Engagement. So get out there. Stand for office. Join. Volunteer.
  4. Now is the time to prepare for illness – keep a stock of remedies, including useful antibiotics (although know what you are doing, don’t just buy them and take them), vitamin C supplements (I like elderberry syrup), painkillers, herbs, and tools for handling even serious illness by yourself. In the event of a truly severe epidemic of flu or other illness, avoiding illness and treating sick family members at home whenever possible may be safer than taking them to over-worked and over-crowded hospitals (or, it may not – but planning for the former won’t prevent you from using the hospital if you need it).
  5. Most schools would be delighted to have volunteers come in and talk about conservation, gardening, small livestock, home-scale mechanics, ham radio, etc…, and most homeschooling families would be similarly thrilled. Consider offering to teach something you know that will be helpful post-peak (although I wouldn’t recommend discussing peak oil with any but the oldest teenagers, and not even that without their parents permission
  6. Now is the time to convince your business, synagogue, church, school, community center to put a garden on that empty lawn. If you start the campaign now, you can be ready to plant in the spring. Produce can be shared among participants or offered to the needy.
  7. The one-two punch of rising heating oil and gas prices may well be what is needed to make your family and friends more receptive to the peak oil message. Try again. At the very least, emphasize the options for mitigating increased economic strain with sustainable practices.
  8. Get together with neighbors and check in on your area’s elderly and disabled people. Make a plan that ensures they will be checked on during bad weather, power outages, etc… Offer help with stocking Up for winter, or maintaining equipment. And watch for signs that they Are struggling economically.
  9. Work on raising money and getting help with local poverty-abatement Programs. After the holidays, people struggle. They get hungry and cold. Remember, besides the fact that it is the right thing to do, the life you save May be your own.
  10. Get out and enjoy the cold weather. It is hard to adapt to colder Temperatures if you spend all your time huddled in front of a heater. Ski, Snowshoe, sled, shovel, have a snowball fight, build a hut, go winter Camping, but get comfortable with the cold, snowy world around you.
  11. Have your chimney(s) inspected, and learn to clean your own. Learn to care for your kerosene lamps, to use candles safely, and how To use and maintain your smoke and CO detectors and fire extinguishers. Winter is peak fire season, so keep safe.
  12. Grow sprouts on your windowsill.
  13. Now is an excellent time to reconsider how you use your house. Look around – could you make more space? House more people? Do projects more efficiently? Add greenhouse space? Put in a homemade Composting toilet? Work with what you have to make it more useful.
  14. If a holiday gift exchange is part of your life, make most of your gifts. Knit, whittle, build, sew, or otherwise create something beautiful for the People you love.
  15. If someone wants to buy you something, request a useful tool or preparedness Item, or a gift certificate to a place like Lehmans or Real Goods. Considering giving Such gifts to friends and family – a solar crank radio, an LED flashlight, cast iron pans, These are useful and appreciated items whether or not you believe in peak oil.
  16. Do a dry run in the dead of winter. Turn out all the power, turn off the water. Turn off all fossil-fuel sources of heat, and see how things go for a few days. Use What you learn to improve your preparedness, and have fun while doing it.
  17. Learn to mend clothing, patch and make patchwork out of old clothes.
  18. Write letters to people. The post is the most reliable way of communicating, And letters last forever.
  19. Make a list of goals for the coming year, and the coming five years. Start Keeping records of your goals and your successes and failures.
  20. Keep a journal. Your children and grandchildren (or someone else’s) may want To know what these days were like.
  21. Wash your hands frequently, and avoid stress. Stay healthy so that you can be useful To those around you.
  22. For those subject to depression or anxiety, winter can be hard. Find ways to relax, Decompress and use work as an antidote to fear whenever possible. Get outside on sunny Days, and try and exercise as much as possible to help maintain a positive attitude.
  23. Memorize a poem or song every week. No matter what happens to you, no one can ever take away the music and words you hold in your mind. You can have them as comfort and pleasure wherever you go, and in whatever circumstances.
  24. Take advantage of heating stoves by cooking on them. You can make soups or stews On top of any wood stove or even many radiators, and you can build or buy a metal oven That sits on top of woodstoves to bake in.
  25. Winter is a time of quiet and contemplation. Go outside. Hear the silence. Take pleasure in what you have achieved over the past year. Focus on the abundance of this present, this day, rather than scarcity to come.

Followers